Hoppa till innehåll
Free shipping over 3000 kr excl. VAT! Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%
Volume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Two temperatures and an alarm on your phone: how to catch a deviation before the product is ruinedThree measuring points give the correct bore size even when the operator is in a hurryFrom ”It Looks Like a Crack” to a Measurement: A Measuring Loupe with a Glass Scale Gives You Answers Right at the WorkplaceThe hole measured right with two-point measurement but still didn’t fit: how three-point measurement reveals form errorsWhy a Two-Point Measurement Often Shows the Wrong Diameter in a Bore That Is Actually OvalThe temperature excursion happened overnight, but nobody can show when it startedHow to See to the Hundredth Whether a Workpiece Runs Out Before You Clamp ItWhat you can’t see with a loupe shows up on the screen: microscopes with measuring function move inspection to the workbenchMoisture damage only shows up afterwards, but the logger shows when the air started to turnMeasure what a vernier caliper can’t reach: how to check hundredths of a millimetre right at the machineVolume discount: 5 pcs 2% · 10 pcs 3% · 25 pcs 5%Two temperatures and an alarm on your phone: how to catch a deviation before the product is ruinedThree measuring points give the correct bore size even when the operator is in a hurryFrom ”It Looks Like a Crack” to a Measurement: A Measuring Loupe with a Glass Scale Gives You Answers Right at the WorkplaceThe hole measured right with two-point measurement but still didn’t fit: how three-point measurement reveals form errorsWhy a Two-Point Measurement Often Shows the Wrong Diameter in a Bore That Is Actually OvalThe temperature excursion happened overnight, but nobody can show when it startedHow to See to the Hundredth Whether a Workpiece Runs Out Before You Clamp ItWhat you can’t see with a loupe shows up on the screen: microscopes with measuring function move inspection to the workbenchMoisture damage only shows up afterwards, but the logger shows when the air started to turnMeasure what a vernier caliper can’t reach: how to check hundredths of a millimetre right at the machine

The Backing Plate Is Manufactured Oversized, Since It’s the Part That Wears

Published August 28, 2026 at 00:27

A plug gauge measures nothing. It produces no number, no decimal, and no deviation — it settles only one thing: is the hole within tolerance or not?

It does this by being the tolerance. The two ends are manufactured at the limits of the tolerance class, so the tool is essentially the permitted range made from hardened steel.

Pluggmaatt H7 med Go och NoGo paa ett handtag enligt DIN 7162

What it is

A plug gauge in tolerance class H7, Ø60 mm, with Go and NoGo on the same handle.

  • Hardened and ground steel, according to DIN 7162/7164
  • Wear allowance on the Go side
  • Serial number, delivered in a plastic tube with manufacturer’s measurement protocol

Two ends, two different questions

The Go end should enter freely, all the way. It’s manufactured at the lower limit of the hole, so if it passes through, you know the hole isn’t too small. The requirement that it must go in all the way also means it checks more than just diameter: a hole that’s tight somewhere along its depth, or that’s crooked or oval, will stop the Go end even though the opening measured correctly.

The NoGo end should not enter. It sits at the upper limit, and if it passes through, the hole is too large. It’s deliberately made short, since it should only test the diameter — not whether you happen to be holding it at an angle.

Both are needed. Go alone would approve a hole that’s far too large; NoGo alone wouldn’t say anything about whether the hole is even large enough.

The wear allowance is the clever detail

The Go end is the one that gets used. It’s inserted into every hole, every time, and scrapes against the material. So it wears — and it wears smaller, which would eventually let it start entering holes that are actually too tight. A worn Go end approves parts that should be rejected.

That’s why the Go side is manufactured with a small oversize relative to the nominal limit. It gets a margin to wear into before it falls outside its specification, which extends the gauge’s service life in exactly the direction the wear moves.

The NoGo end barely wears at all, since under normal use it never enters anything. It therefore needs no corresponding margin. Two ends on the same tool, with different lifespans — and the design accounts for that.

Why serial numbers and measurement protocols

A plug gauge is a limit in physical form, and limits must be traceable. The protocol states the actual diameters of this specific example, and the serial number ties the data to the tool even if it’s sitting in a box with ten others.

This connects to the wear allowance: since the gauge changes over its lifetime, it must be checked at regular intervals. A plug gauge that has passed its wear limit isn’t broken — it looks exactly the same — but it no longer represents the tolerance it claims to represent.

What it can’t do

It gives no measurement, and therefore no trend. A hole that barely passes and one right in the middle of the tolerance get the same verdict. That means a process slowly drifting toward a limit will look perfectly healthy right up until the day it doesn’t.

That’s where a measuring instrument is superior. On the other hand, a plug gauge takes a few seconds, requires no interpretation, and gives the same answer regardless of who’s holding it — and for a hundred holes in a row, that’s often exactly what you want.

Three typical use cases

  • Acceptance inspection of holes: drilled and reamed holes checked against the drawing’s tolerance class.
  • Incoming inspection: quick sorting of purchased parts.
  • Fixtures and jigs: verification where the range matters, not the exact measurement.

Why it pays off

Tolerance class H7 on a hole of this size is a narrow band, and measuring it with an instrument takes time and requires someone to read and assess the value. A plug gauge shifts the judgment to the hand: it goes in, or it doesn’t.

It’s rarely the most precise inspection that’s the most valuable — it’s the one that actually gets done on every part instead of every tenth.

Read more about the H7 plug gauge Ø60 mm →

More news

All news